Видео

Does anyone knows what is the torque specs on the axle ring nut?

Exactly what i was looking for, thanks man.

This guys full of shit, nobody likes stock wheels or factory rake😂

Traduce al español

Great video.....my dad used to just put paper towel on the spark hole and turn crank and once you here a pop from compression blowing paper towel out you know your on compression

I have a 98 Chevy Silverado my ac not going on high wat could be the problem

My ac not going on high wat could it be

From one tec to another excellent video brother

Talk about going around your elbow to get to your ass! Is somebody going to tell me this is better than the 95's and earlier?😡

Helpful video. Thanks

I drive a van that does it about 2 hours every where 😮‍💨 I’m always tell everyone better hope you said your prayers today

I had p1345 code and installed a new distributor when i noticed damage on original i was hoping that would fix code but it hasnt i set the rotor to spark plug 1 before switching and made sure was flush to engine vehicle starts and runs but still same code think i need to get hooked up to scan tool

Great video. Thanks!

You don't have to spend all that on blue devil . Its just sodium silicate . You can get the chemical online

Is the bolt you removeef a Basic R/H THREADED bolt or L/H THREADED. ITS IMPORTANT to explain that .thanks

thank you, i just changed mine thanks to you!

Half moons should have been done and then any dirt/grime that falls on the cam lobes should be wiped off and then use a separate clean rag dipped in oil to wipe them so they are not dry when engine is started. Other than that pretty solid diy video.

Im doing brake pads on 89 pickup im not seeing the metal clips on old caliper that hold pads. U shaped. Are they not on these trucks. I picked some up but not seeing where they go.

You should NOT have too move crack once TB is off. LINE UP marks before hand..TB should go on if set 50 degrees past TDC....

Timing belt don't look bad. I inspect TB before replacing.

Dude you over complicated stuff at one point you said if you have the valve cover off then just look at the valves open and close to see when your in compression cycle right, I'm willing to bet a nickel that if people have there valve cover off already they already know how to install there distributor ok so it's useless information and confusing...I say all that only cause it confused the hell out of me... Ok so instead remove spark plug for cylinder no. 1 stuff a small wad of tp or a piece of paper napkin just make sure to kinda plug the hole up dont dare try or even think of stuffing it as if it was a turkey ok you then remove the distributor cap so the engine won't start bump the key ok as soon as its in compression cycle the air will blow the tp or napkin off then simply rotate engine with a socket on the main pulley and line up your timing marks done your TDC NOW you mark your rotor with a permanent maker to where it's pointing remove the distributor screw holding it down in its place now slowly pull distributor up and pay very very good attention cause you now have to set a second mark on distributor cause it will rotate cause of the gear it has at the bottom that engages with your cam ok Now to install transfer your two marks over to new distributor and make sure your rotor is pointing to the second mark you made ok as the distributor drops in place it's going to rotate the same amount it did as when you removed it ending up pointing to your original and first mark you made when you first removed the cap Now if all this is done correctly the timing will be just as it was before you started. Not to difficult but it's very very important that you pay close attention to exactly what your doing and have no distractions. It's also recommended to take video and/or plenty I mean lots of pictures. I personally take a photo of whatever I'm removing right before I do like every nut,bolt,screw,hose,belt,clip well you get the picture ok (lol) Maybe try this method out Disclaimer: I'm not s certified mechanic so don't take this as true and correct in any way shape or form I truly recommend you to seek a certified professional mechanic and I will not be held responsible for any and/or all damages or failures that can occur your at your own risk

Bull crap. What is your air pressure. I'm at 150 psi and it's not working. I guess the factory tighten to freaking much.

Thanks man! Saved me a ton of trouble. Almost bought the hardwire kit.

Great video Buddy

Your videos (this, and the long one) make everything so clear! It crystallised to me the link between TDC on the first cylinder and the spark on the first cylinder’s spark pug. Today i didn’t need to guess and worry - just went ahead and replaced the old plastic distributour with a robust new one. Thanks!

you left finger prints!

Thank's sir Hpy nice day Bless u

Nice Vid..thanks from germany

im just gonna say it if you dont mark it your dodge power rammed. its impossible to find the right angle on oil pump shaft where the rotor ends up pointing at cylinder one. im not talking about turning it with screw driver im talking when distributor finally seats i can never get it pointing at 1

ive followed everything you did. i pulled mine out without marking it. but its impossible to line oil pump shaft to where distriibuter drops down pointing to number one

very informative video. Thank you for posting it. Answered all my questions. I'm going to give this a try.

Does anyone know if it's necessary to put the gear in neutral before turning the camshaft?

My 2015 gmc sierra 2500 HD was EXACTLY the same. Thanks for doing the reading for me.

Saved me a LOT of time! Thanks!

Badass

While you have it apart throw some locking hubs on there to save your CV boots from spinning at high speeds especially at increased angles if lifted. Great video sir.

The thermostat u got is vtec or non vtec

I can’t thank you enough for sharing this info! I was fortunate to be loaned a Milwaukee 18V hammer drill to use with my lisle weighted socket and removal was EFFORTLESS!

bullsi....t !!!!! ....... tries to explain something that he DOESN’T UNDERSTAND

I had to take the whole rocker assembly off to change vvt selniod on my 09 honda 3.5l and I torgued it down evenly and 2 weeks later I started getting misfires on cylinders 4 5 and 6 when cold started only. After some research I discovered its a value issue go figure.

I have a Toyota Camry 2017 petrol I noticed I have a very light vibration when I press accelerate between 40 to 80 I feel it can anyone suggest what kind of problem going on as I am worried about I don’t want to loose my car. And had only 180kms

Great step by step video. But why counter clockwise? Ive seen multiple videos rotate counter clockwise yet the repair manual specifically states clockwise. Depends on the model? Im working on a 2013 pilot. Thanks

My Honda just threw this code and makes a noise when I first start it. I don’t have the funds now but would it be okay to continue driving it for some more weeks

but before it drops down when you wiggled it its not pointing towards one anymore?

Good morning is the crankshaft pulley supposed to wobble at all. And I can hear a noice coming from that area I haven’t done a full inspection?

For the spark plug gaskets does it matter how to install them ? I think I installed them backwards oh man

Very well explained .Best video out there

Is your hose a 3/8th?

Hell yea 💪💪💪

This video helped me out, thank you!